Bilby3D: Router Add-Ons and Spares

General Enquiries:

Phone: Freecall 1800-847-333
Fax: +61 2 8079 5971

Sydney - Alexandria, NSW
More

Unit 23, "The Bourke Centre"

Set Your Store

110 Bourke Road
Ph: 02 8197 3928

Brisbane - Spring Hill, QLD
More

Shop 2, 474 Upper Edward Street

Set Your Store

Ph: 07 3135 9810

Melbourne - Clayton, VIC

Factory A5, 2 Westall Rd, Clayton

Set Your Store

Ph: 03 8080 1200

Head Office - Bega NSW

452 Wyndham Lane, Kanoona. Ph: 02 8197 3930

Click above to set your Store

Router Add-Ons and Spares
Tailstock, 4th axis, spare parts etc.
To view our configuration recommendations for generic routers using Mach3 software or Smooth Stepper controllers Click Here

Related Sub-Categories: Router Bits, Tools and Accessories | Desktop 3D Routers |

ptCoup5-8RD

Coupler 5 to 8mm Rigid

Rigid Coupler for Joining a stepper Motor to a Threaded rod or Leadscrew
Rigid so its great for accuracy when used on a Z-Axis
More

ptCoup6.35-10

Flexible Coupler - 6.35mm to 10mm

This coupler is 25mm outer diameter and 30mm long. It is of the clamping variety
More

ptCoup6.35-8

Shaft Coupler - 6.35 to 8mm

This flexible Shaft Coupler is design to mate between 6.35mm and 8mm shafts
More

ptDriverDM542A

Stepper Motor Driver Board - DM542A

The DM542A is a type of two-phase hybrid stepping motor driver for one motor. It is designed for use with 2-phase hybrid stepper motor of all kinds with 42mm to 86mm outside diameter and less than 4.0A phase current.
Input Voltage: 18VDC to 50VDC.
Input Power: <4A up to 80W
Output Current: 1A - 4.2A(peak)
Inputs and Outputs are opto-isolated.
Overvoltage, under voltage, overcorrect, phase short circuit protection
Operating Temperature: -10 to 45 degreesC
15 channel subdivision and automatic idle-current reduction. 8 channels output phase current setting
Replaces the older MD542 Driver
More

ptBreakBdDB25

Breakout Board with DB25 Male Connector

Board for breaking out the pins on a parallel port cable
More

cncRoutTail

Tailstock for Router 4th Axis

This tailstock is used to hold stil lthe end of the workpiece being held in a 4th axis.
The center is 49mm off the bed. The base is 80x80mm with mounting holes 50mm and 60-70mm apart.
More

cncRoutSpindle800W

Router Spindle - 800W Watercooled

800W, 3 bearing router spindle with water cooling

More

cncRoutSpindle1500W

Router Spindle - 1.5kW Watercooled, 80mm diameter

1500W, 3 bearing router spindle with water cooling
Speed: 6000-24,000rpm - will run lower but with lower torque

More

ptDriverDM420A

Stepper Motor Driver Module - DM420A

The DM420A is a type of two-phase hybrid stepping motor driver for one motor. It is designed for use with 2-phase hybrid stepper motor of all kinds with 20mm to 36mm outside diameter and less than 2.0A per phase current.
Input Voltage: 12VDC to 36VDC.
Input Power: <2A up to 40W
Output Current: 0.44A - 2.83A(peak)
Inputs and Outputs are opto-isolated.
Overvoltage, under voltage, overcorrect, phase short circuit protection
Operating Temperature: -10 to 45 degreesC
15 channel subdivision and automatic idle-current reduction. 8 channels output phase current setting
Replaces the older MD542 Driver
More

cncRoutSpinBr6x3

Spindle Brush - Single

The brushes inside the DC spindle motors eventually wear out (our watercooled spindles are brushless). This item is a replacement.
More

ptCoup8-8

Shaft Coupler - 8 to 8mm

This flexible Shaft Coupler is designed to mate between 8mm and 8mm shafts.
More

ptPump2300

Submersable Water Pump - 2300Lt/Hr

This high capacity pump moves 2200 Litres per Hour, to a height of up to 2.2m. 30W
Most importantly, it has a 19mm outlet which matches the hose fitting on our 6040 series of routers with water cooled spindles
More

Related Sub-Categories:

General Enquiries:

Sydney - Alexandria, NSW
More

Brisbane - Spring Hill, QLD
More