Suits the Creator Pro, Dreamer and Inventor machines as well as a wealth of others. It is not self adhesive and you need Kapton tape to attach to your heat block. More
Hot End - E3D v6 clone - 1.75mm Filament, 0.4mm nozzle
This complete hot end is based on the All-Metal J-Head design as modified by E3D (V6). Includes everything you need, hot-end wise for 1.75mm filament More
Genuine Micro-Swiss all metal hotend upgrade for MK10 style extruders.
MK10 Extruders most notibly used on the FlashForge Dreamer, Inventor1 and Pro 2016 and Dremel Idea Builder. It also fits the Wanhao i3 and Cocoon More
These straight cut gears have the advantage over a hobbed gear in that the profile of the teeth is much deeper - so they dont get clogged as quickly - they get a better grip on the filament for longer. More
This 1 inch wide ceramic tape is used to wrap your heater block and reduce heat transfer to both the extruder and your work piece. Fix by wrapping in kapton tape.
The tape on your Makerbot, MBot3D or Reprap will need replacing from time to time, especially when a print fails and the melted plastic gets caught up in the print head - it can sometimes stick to the ceramic tape and rip it on removal - careful not to pull on the temperature sensor wire! More
MicroSwiss All Metal Hotend Kit for FlashForge Finders, Guiders, Inventor 2
Genuine Micro-Swiss all metal hotend upgrade for the FlashForge Finder, FinderPlus, Guider, Guider 2 and Inventor2
Comes with 0.4mm nozzle, range of other sizes available More
Pre-Cut Ceramic tape with Kapton for Finder, Inventor2, Guider2
Suits the Finder, Inventor2, Inventor2s, Inventor2SE, Guider, Guider2 and Guider2s machines as well as many others. It is not self adhesive and you need Kapton tape to attach to the heater block. More
0.4mm Nozzle for MK10 Micro Swiss All Metal MK10 Hotend Kit
This is Micro Swiss MK10 All Metal Hotend ONLY style nozzle, it will ONLY fit the New MK10 All Metal Hotend. This nozzle has completely different internal dimensions to work with our Micro Swiss thermal barrier tube More
FlashForge Thermocoupler - Short with Molex connector
Genuine FlashForge thermocoupler with 11cm lead length and Molex connector for the Finder, Inventor2 and Guider which have a terminal board on the extruder carriage. More
Genuine FlashForge thermocoupler
M4 brass fitting at sensing end (Note: our other thermocouplers and heater blocks are all M3)
Crimped terminals at motherboard end
~11cm lead length - Suited to the FlashForge Dreamer which has a terminal board on the extruder carriage More
0.6mm Nozzle for MicroSwiss All Metal MK10 Hotend Kit
This is Micro Swiss MK10 All Metal Hotend ONLY style nozzle, it will ONLY fit the New MK10 All Metal Hotend. This nozzle has completely different internal dimensions to work with our Micro Swiss thermal barrier tube
More
0.2mm Nozzle for Micro Swiss All Metal MK10 Hotend Kit
This is Micro Swiss MK10 All Metal Hotend ONLY style nozzle, it will ONLY fit the New MK10 All Metal Hotend. This nozzle has completely different internal dimensions to work with our Micro Swiss thermal barrier tube More
Heater Cartridge for FlashForge 3D Printers Dreamer and Inventor 1 only
Genuine Spare part for FlashForge Dreamer and Inventor 1 only heater cartridge.
Note : Flashforge Creater Pro cable is different (see image 3, ptHeatCart4024)
Flashforge Finder, Guider (1 and 2) and Inventor2 also have a short heater. This is not compatible
More
0.8mm Nozzle for MicroSwiss All Metal MK10 Hotend Kit
This is Micro Swiss MK10 All Metal Hotend ONLY style nozzle, it will ONLY fit the New MK10 All Metal Hotend. This nozzle has completely different internal dimensions to work with our Micro Swiss thermal barrier tube
More
This complete hotend kit from RepRap discount includes; nozzle, heater block, barrel/heat barrier, fined heat sink, heater cartridge, thermistor, fan, mount and more in a plastic case More
This heater cartrige has short (10cm long) cables with a molex male pin connector. The cartrige is 23mm long and 6mm in diameter. It is made in Australia by Bilby3D and is a non-genuine exchange for the Makerbot Replicator 2 and 2X heater cartrige. More
Hot End - E3D v6 version - 3mm Filament, 0.4mm nozzle
This complete hot end is based on the All-Metal J-Head design as modified by E3D (V6). Includes everything you need, hot-end wise for 3mm filament More
For Hexagon, JHead, UBis Hot Ends amoungst many others. This is an Aluminium Mounting Plate designed for use with many different hot-ends and extruders. It is used in RepRap Prusas, Huxleys and many others which is why it has become the standard.
Width: 30mm
Length: 70mm
Thickness: 4.5 More
This tube is an improvement over the stock MakerBot Replicator 1 and MakerBot Replicator 2 thermal barrier tube. Also used on many other types of 3D Printers More
0.3mm Nozzle for Micro Swiss All Metal MK10 Hotend Kit
This is Micro Swiss MK10 All Metal Hotend ONLY style nozzle, it will ONLY fit the New MK10 All Metal Hotend. This nozzle has completely different internal dimensions to work with our Micro Swiss thermal barrier tube. More
This tough extruder includes a greabox for extra filament feeding torque as well as everything you need to take filament from you spool through to pushing it into your hotend.
This complete hotend kit from RepRap discount includes; nozzle, heater block, barrel/heat barrier, fined heat sink, heater cartridge, thermistor, fan, mount and more in a plastic case More
This aftermarket heater block (also known as a thermal core) is a drop-in replacement for the UP! UP! Plus, Plus 2 and UP Mini printer. These printers are sold under the brands: Afinia, TierTime and 3D Printing Systems
Stripped the thread when changing nozzles? This is the part for you More
Ever had a print fail because you leave the machine to make a beverage and the filament runs out?
We have, so we developed a simple mechanism to sound an alarm to warn you when the end of the filament reaches the end of your filament guide tube.
This version comes with a mounting bracket designed so the sensor fits between the filament spool and the end of the guide tube on a Replicator 2 or 2x. You dont have to use the bracket and could mount it with double sided tape, zip ties or the bolts running through the body on almost any machine.
Requires a 9V battery (not included). The power is only used when the alarm sounds, so if you use an alkaline battery (which have minimal self-discharging) it will not go flat for a long, long time - we estimate over 1 year. More
Replicator 1/2 - Extruder Upgrade Kit (injection moulded) - Left Lever
This injection molded upgrade is designed to fit the Makerbot Replicator 1 Twin left extruder. IT DOES NOT FIT the Repliactor 2X which requires a thicker drive system. It also is NOT suitable for the Replicator 2 or single extruder machines! More
This Makerbot Brand injection molded upgrade is designed to fit the Makerbot Replicator 2, however it is also backward compatible to the original Replicator (ply wood) Single and right extruder on the Twin. More
Printrbot Aluminum direct drive extruder is a work of art. Its elegant design makes it really stand out. Plus it is reversible to accommodate dual extruder setups. It is easy to adjust but rock solid. It holds both the 1.75 Ubis Ceramic and Ubis Catridge hot ends perfectly. Enjoy the benefits of machined aluminum.
* Machined drive gear included. Motor not included More
Use this for sensing the temperature of your hot end, heated bed or whatever you can think of
Specs:
100kOhm
Tolerance +-10%
Beta Value(K) 4036K
Operating Temperature: -60 to 300 degC
Bead Dia 2.13mm length 4.5mm
Lead Length 67mm More
Sydney - Alexandria, NSW
Melbourne - Clayton, VIC
3D Printing
3D Printer Filament
Brisbane - Spring Hill, QLD
Bilby 3D Technical Support
3D Printer Service and Repair
Courses and Training
3D Scanners
Parts and Spares
Tools & Jigs