This is Micro Swiss MK10 All Metal Hotend ONLY style nozzle, it will ONLY fit the New MK10 All Metal Hotend. This nozzle has completely different internal dimensions to work with our Micro Swiss thermal barrier tube More
This is Micro Swiss MK10 All Metal Hotend ONLY style nozzle, it will ONLY fit the New MK10 All Metal Hotend. This nozzle has completely different internal dimensions to work with our Micro Swiss thermal barrier tube More
This is Micro Swiss MK10 All Metal Hotend ONLY style nozzle, it will ONLY fit the New MK10 All Metal Hotend. This nozzle has completely different internal dimensions to work with our Micro Swiss thermal barrier tube
More
PLA Blend Filament - Magnetic Iron - 1.75mm - 125g Coil
This amazing filament is a blend of PLA and carbon Fibre by ProtoPasta in the USA.
Proto-pasta Magnetic Iron PLA - as its name implies - responds to magnets and behaves similarly to pure iron, even to the point of rusting! Magnetism opens up a new world of practical applications and fun creations.
It extrudes at 190-200 degrees c on a cold bed. We have tested on buildtak wit glue stick and it sticks well. Prints best at thicker resolutions like 300 microns, but will look like 100 micron. Our tests showed no spider webbing at all, and models held water after printing. It can lift in unsupported areas, but quickly recovers on the next layer. Sands nicely with very course sandpaper. Can get rust effect by submerging in with salty water for 2-3 hours. In our tests it was not too abrasive on nozzle, but recommend a wear resistant nozzle. More
Proto-pasta Stainless Steel PLA is a dense material that prints as easily as standard PLA but results in heavy prints that can be finished post-print to achieve amazing results. Perfect for jewelry, costumes, props, figurines, crafting, robots, and more!
In filament form, SSPLA is slightly more brittle than standard PLA, and requires extra care when handling.
More
PLA Blend Filament - Carbon Fiber - 1.75mm - 125g Coil - UNTIL SOLD OUT
This amazing filament is a blend of PLA and carbon Fiber by ProtoPasta in the USA. It prints easily at 230-245 degrees on a cold bed. We used glue on a glass bed for our test. Tendancy to leave small balls/pimples on surface which easily clean up. Will wear nozzle so we advise using a wear resistant nozzle (sold seperately). Produces impressively strong models with minimum fuss and difficulty. More
PLA Blend Filament - Magnetic Iron - 1.75mm - 500g Spool
This amazing filament is a blend of PLA and carbon Fibre by ProtoPasta in the USA.
Proto-pasta Magnetic Iron PLA - as its name implies - responds to magnets and behaves similarly to pure iron, even to the point of rusting! Magnetism opens up a new world of practical applications and fun creations.
It extrudes at 190-200 degrees c on a cold bed. We have tested on buildtak wit glue stick and it sticks well. Prints best at thicker resolutions like 300 microns, but will look like 100 micron. Our tests showed no spider webbing at all, and models held water after printing. It can lift in unsupported areas, but quickly recovers on the next layer. Sands nicely with very course sandpaper. Can get rust effect by submerging in with salty water for 2-3 hours. In our tests it was not too abrasive on nozzle, but recommend a wear resistant nozzle. More
This is Micro Swiss MK10 All Metal Hotend ONLY style nozzle, it will ONLY fit the New MK10 All Metal Hotend. This nozzle has completely different internal dimensions to work with our Micro Swiss thermal barrier tube
More
This is Micro Swiss MK10 All Metal Hotend ONLY style nozzle, it will ONLY fit the New MK10 All Metal Hotend. This nozzle has completely different internal dimensions to work with our Micro Swiss thermal barrier tube. More
This wear resistant nozzle by AVN/Micro Swiss is the standard size for a range of printers has a 5mm long M6 thread and 0.4mm tip hole. Total Length 13mm. The main hole is for filament with 2.85/3mm diameter or 3mm OD PTFE tube.
0.6mm Nozzle - M6 thread and Wear Resistant TwinClad coating
This wear resistant nozzle by AVN/Micro Swiss is the standard size for a range of printers has a 5mm long M6 thread, but has a larger and 0.6mm hole, which it sometimes used for faster printing and with metal and PETG filaments. Total Length 13mm
More
TwinClad Coated 0.4mm nozzle for Zortrax M200 + UP Plus 2 printers
This nozzle from US firm MicroSwiss fits Zortrax M22, Afinia and UP! style printers, it is made from a 360 brass base material and plated with TwinClad XT coating.
Real Metal PLA Blend - 1.75mm - Copper Filament - 750g Spool
This amazing ColorFabb filament is a blend of 80% fine Copper particles and PLA and prints on standard desktop 3D Printers at PLA settings. It is very brittle in the filament state and seems like it would not be strong, but when you print and the melted PLA bonds and blends with the copper it becomes very strong. More
Proto-Pasta Stainless Steel PLA is a dense material that prints as easily as standard PLA but results in heavy prints that can be finished post-print to achieve amazing results. Perfect for jewellery, costumes, props, figurines, crafting, robots, and more! More
Proto-Pasta Stainless Steel PLA is a dense material that prints as easily as standard PLA but results in heavy prints that can be finished post-print to achieve amazing results. Perfect for jewellery, costumes, props, figurines, crafting, robots, and more! More
This amazing filament is a blend of PLA and carbon Fiber by ProtoPasta in the USA. It prints easily at 230-245 degrees on a cold bed. We used glue on a glass bed for our test. More
Proto-pasta Stainless Steel PLA is a dense material that prints as easily as standard PLA but results in heavy prints that can be finished post-print to achieve amazing results. Perfect for jewelry, costumes, props, figurines, crafting, robots, and more!
In filament form, SSPLA is slightly more brittle than standard PLA, and requires extra care when handling.
Processing is comparable to standard PLA (extrudes at 190-240C). No heated bed required. Due to increased brittleness, process may be less consistent on smaller nozzles and/or bowden type machines. More
This amazing filament is a blend of PLA and carbon Fiber by ProtoPasta in the USA. It prints easily at 230-245 degrees on a cold bed. We used glue on a glass bed for our test. Tendancy to leave small balls/pimples on surface which easily clean up. Will wear nozzle so we advise using a wear resistant nozzle (sold seperately). Produces impressively strong models with minimum fuss and difficulty. More
This amazing filament is a blend of PLA and carbon Fiber by ProtoPasta in the USA. It prints easily at 230-245 degrees on a cold bed. We used glue on a glass bed for our test. Tendancy to leave small balls/pimples on surface which easily clean up. Will wear nozzle so we advise using a wear resistant nozzle (sold seperately). Produces impressively strong models with minimum fuss and difficulty. More
This amazing ColorFabb filament is a blend of 80% fine Copper particles and PLA and prints on standard desktop 3D Printers at PLA settings. It is very brittle in the filament state and seems like it would not be strong, but when you print and the melted PLA bonds and blends with the copper it becomes very strong. More
The material is still in beta, which means colorfabb are still working on the formulation to get the best possible performance. It is a high metal content abbrassive filament that polishes up to be a metal print with a lovely golden shine it shows when polished to perfection.
More
The material is still in beta, which means colorfabb are still working on the formulation to get the best possible performance. It is a high metal content abbrassive filament that polishes up to be a metal print with a lovely golden shine it shows when polished to perfection.
More
This wear resistant nozzle by AVN/Micro Swiss is the standard size for a range of printers
It has a Wear Resistant High Lubricity TwinClad XT Coating this makes it a excellent choice when printing with abrasive/wearing material such as Bronze, Copper, Alumininium or Carbon Fiber filament.
More
This wear resistant nozzle by AVN/Micro Swiss is the standard size for a range of printers
It has a Wear Resistant High Lubricity TwinClad XT Coating this makes it a excellent choice when printing with abrasive/wearing material such as Bronze, Copper, Alumininium or Carbon Fiber filament.
More
Sydney - Alexandria, NSW
Melbourne - Clayton, VIC
3D Printing
3D Printer Filament
Brisbane - Spring Hill, QLD
Bilby 3D Technical Support
3D Printer Service and Repair
Courses and Training
3D Scanners
Parts and Spares
Tools & Jigs