Bilby 3D
Your Account
Your Account
Shop Locations
Bilby 3D
- Experts in 3D
X Close

General Enquiries:

Phone: Freecall 1800-847-333
Fax: +61 2 8079 5971

Sydney - Alexandria, NSW

Unit 23, "The Bourke Centre"
Set Your Store
110 Bourke Road
Ph: 02 8197 3928

Brisbane - Spring Hill, QLD

Shop 2, 474 Upper Edward Street
Set Your Store
Ph: 07 3135 9810

Melbourne - Clayton, VIC

Setting up at A5, 2 Westall Rd, Clayton
Set Your Store
Ph: 03 8080 1200

Head Office - Bega NSW

452 Wyndham Lane, Kanoona. Ph: 02 8197 3930

Click above to set your Store
X Close

Log In to your Account

Forgot Password?


Once logged in, you can view your previous orders and tracking details
and save time at checkout by not having to enter your details again

New to Bilby3D?

This item is no longer available. This information is for reference only

MakeX M-One Resin Printer

This item is no longer available, you cannot order it

The M-One Printer offers great value for those who want to get in to UV curing resin printing, with a decent build size and low cost. The propriatary software, XMaker, is a little finnicky to use, but with great online support - with YouTube videos for everything from unboxing and setting up, using the software and even refreshing the resin tank, we think youll like it.
- Smooth surface finish on prints, as you would expect with resin printouts
- Build volume: 145 x 110 x 170 mm (W x D x H)
- 140 micron (0.14mm) minimum feature size (X and Y)
- 15-105 microns layer thickenss
- DLP Projector (1024 x 768 pixels, 3000 ANSI Lumens, 15000:1 contrast ratio, 5000hr lamp life) ready to use, upgradable with a higher resolution projector later
- USB Interface and screen

Please note: due to manufacturers terms, we can currently only offer 3 months warranty on these machines

Features Specs Support

Next More Information


Related Products:
Buy Now
M-One Resin Tank - Permanent Vat
Genuine MakeX Resin Tank/Vat for the M-One, XGA and HD models.
This is the Flex Vat V2.
This breakthrough technology does away with the old silicon resin coated vats, which are easily damged and become cloudy after as few as 10 prints in the same spot.
Instead this tank had a flexible FET film, which lessens the load on the machine when peeling off the print after each layer, PLUS it is easily and (relatively) inexpensively replaced!
Each tank comes with 1 film pre-installed, and a spare for you to use later.

Assembly notes:
- Peel the protective paper of the perspex panel, this sits in the base piece with the perspex UP, so the lower piece is raised in the middle
- Place the tank itself on top, so the raised section pulls the film tight
- Add the fixing screw with spring - wound in about half way only
Buy Now
M-One Build Platform
Genuine MakeX Build Platform / Table for the M-One, XGA and HD models.
Has adjustment screws for levelling and a super thick aluminium platform

All prices are in Australian Dollars and include GST. Standard Postage & Handling with Australia is $12 flat rate, free for orders over $350. Express Post starts at $14

Copyright 2017 Bilby3D. "Bilby3D" and the Bilby Logo are registered Trademarks of Bilby Publishing, used with Permission.
Google+  Facebook  Twitter  LinkedIn
Bilby 3D Pty. Ltd. Phone 1800-847-333 International +61 2 8197 3928
Australian Distributors of desktop sized 3D Printers (Raise3D, Robo3D, FlashForge, Roland, Da Vinci, Reprap, Makerbot & UP printers), 3D Scanners, Tools & Parts
Sydney: 23 / 110 Bourke Rd, Alexandria, NSW 2015, Australia
Brisbane: 2 / 474 Upper Edward St, Spring Hill, QLD 4000
Melbourne: A5 / 2 Westall Rd, Clayton, VIC 3168
Bega Head Office: 452 Wyndham Lane, Kanoona 2550