The DM860A is a type of two-phase hybrid stepping motor driver for one motor. The drive voltage is from 24VDC to 80VDC. It is designed for use with 2-phase hybrid stepper motor of all kinds with 57mm to 110mm outside diameter and less than 8.0A phase current.
Inputs and Outputs are opto-isolated.
Overvoltage, under voltage, overcorrect, phase short circuit protection
14 channels subdivision and automatic idle-current reduction. 8 channels output phase current setting
Holding torque when the DM860A is run under high speed is also significantly higher than other two-phase drivers, what’s more, the positioning accuracy is also higher.
It is widely used in middle and big size numerical control devices such as curving machine, CNC machine, and computer embroider machine, packing machines and so on.
Replaces the older MD882 Driver
Related Products:
Buy Now
Power Supply - 24V, 360W, 15A
Switching power supply with temperature controlled fan and indicator LED
Buy Now
Stepper Motor - Nema 34
Nema 34 motor with 4 wires and a holding torque of 1150N.cm
Length 150mm, 86x86mm face, 69.6mm between the holes
Shaft Diameter is 14mm, 13mm across flats
Step angle is 1.8 degrees, rated current 3.5A per phase, phase resistance 1.8 Ohms and Inductance 21mH
Buy Now
Stepper Motor - Nema 23 - 90
Nema 23 motor, step angle of 1.8 degrees, with 6 wires and a Uni-Polar holding torque of 90N.cm (127.5 oz-in or 9.18kgf-cm), Bipolar holding torque is 126N.cm
Length 54mm, 56x56mm face, 47x47mm between the holes
Shaft diameter is 6.35mm, length 21mm, no flat
Motor Phase Voltage: 3.6V
Insultaion Resistance 100M Ohm Min. 50V DC, Dielectric Strength 500V AC for 1 minute
Rated current 2A per phase, phase resistance 1.5 Ohms and inductance 2.5mH
Buy Now
Stepper Motor - Nema 23
Nema 23 motor. Step angle is 1.8 degrees, with 4 wires and a holding torque of 250N/cm.
Shaft diameter is 6.3mm
Buy Now
Stepper Motor Driver Module - DM420A
The DM420A is a type of two-phase hybrid stepping motor driver for one motor. It is designed for use with 2-phase hybrid stepper motor of all kinds with 20mm to 36mm outside diameter and less than 2.0A per phase current.
Input Voltage: 12VDC to 36VDC.
Input Power: <2A up to 40W
Output Current: 0.44A - 2.83A(peak)
Inputs and Outputs are opto-isolated.
Overvoltage, under voltage, overcorrect, phase short circuit protection
Operating Temperature: -10 to 45 degreesC
15 channel subdivision and automatic idle-current reduction. 8 channels output phase current setting
Replaces the older MD542 Driver
Buy Now
Stepper Motor Driver Board - DM542A
The DM542A is a type of two-phase hybrid stepping motor driver for one motor. It is designed for use with 2-phase hybrid stepper motor of all kinds with 42mm to 86mm outside diameter and less than 4.0A phase current.
Input Voltage: 18VDC to 50VDC.
Input Power: <4A up to 80W
Output Current: 1A - 4.2A(peak)
Inputs and Outputs are opto-isolated.
Overvoltage, under voltage, overcorrect, phase short circuit protection
Operating Temperature: -10 to 45 degreesC
15 channel subdivision and automatic idle-current reduction. 8 channels output phase current setting
Replaces the older MD542 Driver
Buy Now
Breakout Board with DB25 Male Connector
Board for breaking out the pins on a parallel port cable
Buy Now
Power Supply - 60V, 350W. 5.85A
This power supply is designed to work with our heavy duty CNC kit parts.
Input: 110V/6.5A or 220V/4A selected by switch
Output: 60V 5.85A - 3 pairs of screw terminals
Has Over-Voltage and Over-Temperature protections
Adjustable voltage for fine tuning +-5V
Internal Fan switches on automatically with temperature
Indicator LED shows operation
Sydney - Alexandria, NSW
Melbourne - Clayton, VIC
Bilby 3D Technical Support
3D Printer Service and Repair
3D Printing & Prototyping Service
Courses and Training
3D Printing
3D Printer Filament
Brisbane - Spring Hill, QLD
3D Scanners
3D Routers
Parts and Spares
Tools and Jigs
Gifts and Samples
Software
Books and Posters