Bilby 3D
Your Account
Your Account
Shop Locations
Bilby 3D
- Experts in 3D
X Close

General Enquiries:

Phone: Freecall 1800-847-333
Fax: +61 2 8079 5971

Sydney - Alexandria, NSW

Unit 23, "The Bourke Centre"
Set Your Store
110 Bourke Road
Ph: 02 8197 3928

Brisbane - Spring Hill, QLD

Shop 2, 474 Upper Edward Street
Set Your Store
Ph: 07 3135 9810

Melbourne - Clayton, VIC

Setting up at A5, 2 Westall Rd, Clayton
Set Your Store
Ph: 03 8080 1200

Head Office - Bega NSW

452 Wyndham Lane, Kanoona. Ph: 02 8197 3930

Click above to set your Store
X Close

Log In to your Account

Forgot Password?


Once logged in, you can view your previous orders and tracking details
and save time at checkout by not having to enter your details again

New to Bilby3D?

PEI Bed Tape - 400 x 400mm
Stock Code: ptTapePEI400
Select Your Store for Click and Collect

5+ Ready for Despatch

This PEI (Ultem) Sheet comes complete with a sheet of 3M 468MP Adhesive to fix it to your bed
Size 400 x 400mm. 0.8mm thick
Single Sheet

Features Specs Support
PEI is the build surface of choice for printing ABS. It bonds incredibly while hot, making lifted prints a thing of the past, and when cool the printed part just pops right off. It is also a permemnent build plate solution. Its thicker and stiffer than other build surfaces and can be cleaned and refreshed a number of ways.


PLA - PEI adheres to PLA quite well, but not as well as Flashforges Blue Bed Tape. It requires a very clean surface, and a good first layer. If adhesion is poor, clean the bed with Isopropyl alcohol and reduce the nozzle offset. Glue stick can be used on PEI to increase adhesion. Bed temperature should be 50 - 55 degrees.

ABS - PEI loves ABS, sometimes a little too much. If your parts do not come off easily when cool youll need to increase your nozzle offset. You should have a very difficult time removing the print while the bed is hot, and an easy time when cold. Bed temperature should be 100 - 110 degrees.

PETG - PEI and PETG are in the same family of plastics and can permanently bond. Keep a healthy nozzle offset and its safest to print to a layer of glue stick. Removing PETG parts from PEI is easier while the bed is somewhat hot. Bed temperature should be 85 - 90 degrees, and remove parts around 40 - 60 degrees.

PEI is best cleaned with Isopropyl alcohol. To refresh the surface better heat the bed to 100 degrees, unplug your printer from the wall and lay a damp towel over the bed for 5 minutes, then wipe off any remaining moisture and youre good to print. For a heavily worn surface a light sand with some high-grit sandpaper will make the PEI stick even better than new. After 6 months of printing Ive had to use the soak trick twice, and never needed to touch it with sandpaper.
To remove glue-stick mild detergent and a damp cloth will do the trick.


This product is in the categories:

Related Products:
Buy Now
PEI Bed Tape - 214 x 214mm
This PEI (Ultem) Sheet comes complete with a sheet of 3M 468MP Adhesive to fix it to your bed
Size 214 x 214mm
Single Sheet
Buy Now
PEI Bed Tape - 300 x 300mm
This PEI (Ultem) Sheet comes complete with a sheet of 3M 468MP Adhesive to fix it to your bed
Size 300 x 300mm. 0.8mm thick
Single Sheet

All prices are in Australian Dollars and include GST. Standard Postage & Handling with Australia is $12 flat rate, free for orders over $350. Express Post starts at $14

Copyright 2018 Bilby3D
Bilby 3D Pty. Ltd. Phone 1800-847-333 International +61 2 8197 3928

Australian Distributors of desktop sized 3D Printers (Raise3D, FlashForge, Roland, Reprap, Makerbot & UP printers), 3D Scanners, Tools & Parts

Sydney: 23 / 110 Bourke Rd, Alexandria, NSW 2015, Australia

Brisbane: 2 / 474 Upper Edward St, Spring Hill, QLD 4000

Melbourne: A5 / 2 Westall Rd, Clayton, VIC 3168