Prices + Stock updated 24 Sep @ 18:10
PLA Blend Filament - Carbon Fibre - 1.75mm - 750g Spool
ColorFabs first special filament based on the Amphora 3D polymer. Reinforced with 20% specially sourced carbon fibers, this filament is perfect for parts which need high stiffness. XT-CF20 has a beautiful matte surface finish when printed.
Features
Specs
Support
Key Features:
Extreme High Flex Modulus (6.2 GPa) / twice as stiff as PLA
Moderate strain at break (8-10%), so no extreme brittle filament, but toughness
High Glass Temp. (Tg = 80degC)
Very high Melt strength
Very high Melt Viscosity
Good dimensional accuracy and stability
Low odor / Styrene Free solution
Easy processing on many platforms
High attractive matt black surface
Printing Tips/settings
Temp : 240-260degC
Speed : 40-70mm/s
Bed Temp : 60-70c
Bed surface : Glue stick on glass
NOTE CARBON FIBER IS ABRASIVE: A special point of attention is the abrasive nature of the carbon fibers. In general these fibers will accelerate the nozzle-wear of brass nozzles, much faster than unfilled filaments. Therefore we recommend you use coated nozzles or nozzles made from Stainless steel or hardened copper alloys.
Next
More Information
Dimensions: 200x200x59
Next
This product is in the categories:
Related Products:
Buy Now
PLA Blend Filament - Carbon Fiber - 1.75mm - 500g Spool
This amazing filament is a blend of PLA and carbon Fiber by ProtoPasta in the USA. It prints easily at 230-245 degrees on a cold bed. We used glue on a glass bed for our test. Tendancy to leave small balls/pimples on surface which easily clean up. Will wear nozzle so we advise using a wear resistant nozzle (sold seperately). Produces impressively strong models with minimum fuss and difficulty.
Buy Now
PLA Blend Filament - Carbon Fiber - 1.75mm - 125g Coil - UNTIL SOLD OUT
This amazing filament is a blend of PLA and carbon Fiber by ProtoPasta in the USA. It prints easily at 230-245 degrees on a cold bed. We used glue on a glass bed for our test. Tendancy to leave small balls/pimples on surface which easily clean up. Will wear nozzle so we advise using a wear resistant nozzle (sold seperately). Produces impressively strong models with minimum fuss and difficulty.
Buy Now
PLA Blend Filament - 2.85mm - Carbon Fiber - 500g Spool
This amazing filament is a blend of PLA and Carbon Fiber by ProtoPasta in the USA.
It prints easily at 230-245 degrees on a cold bed. We used glue stick on a glass bed for our test.
Buy Now
0.4mm Nozzle - M6 thread and Wear Resistant Twin Clad coating
This wear resistant nozzle by AVN/Micro Swiss is the standard size for a range of printers
It has a Wear Resistant High Lubricity TwinClad XT Coating this makes it a excellent choice when printing with abrasive/wearing material such as Bronze, Copper, Alumininium or Carbon Fiber filament.
Buy Now
High Temp Resistant Carbon Fiber PLA - 1.75mm, 3kg Spool
High Temperature Resistant (Annealable) Carbon Fiber / PLA Blend - on a large 3kg Spool
Buy Now
High Temp Resistant PLA - Carbon Fibre - 1.75mm - 500g Spool
New High Teperature Resistant (annealable) Carbon Fiber / PLA Blend
All prices are in Australian Dollars and include GST. Standard Postage & Handling with Australia is $12 flat rate, free for orders over $350. Express Post starts at $14
Sydney - Alexandria, NSW
Melbourne - Clayton, VIC
3D Printing
3D Printer Filament
Brisbane - Spring Hill, QLD
Bilby 3D Technical Support
3D Printer Service and Repair
Courses and Training
3D Scanners
Parts and Spares
Tools & Jigs