Delivery, unpacking and setup of a Bilby3D supplied desktop 3D printer within 40km of our Brisbane base in Spring Hill.
This does not include anything other than basic training on the use of the machine. Additional Training available separately.

Delivery, unpacking and setup of a Bilby3D supplied desktop 3D printer within 40km of our Melbourne base in Clayton.
This does not include anything more than very basic training on the use of the machine. Additional training available separately

This is genuine FlashForge 3D Printer Filament.
The spool fits in the draw of the Finder, Inventor 2/2S/2SE and on the holders inside the Dreamer / Inventor

This is genuine FlashForge 3D Printer Filament.
The spool fits in the draw of the Finder, Inventor 2/2S/2SE and on the holders inside the Dreamer / Inventor

This 3D printer for the adventurous, experimental and experienced 3D printing enthusiaster. Put simply it is better than the Replicator 2, with a 100 micro resolution and provides high quality prints in ABS or PLA with the added benefits of duel extrusion, cast aluminium build plate, enclosed print chamber and pressure based filament feeder system.

One replacement foot for a Flashforge Dreamer and Inventor 1

Ever had a print fail because you leave the machine to make a beverage and the filament runs out?
We have, so we developed a simple mechanism to sound an alarm to warn you when the end of the filament reaches the end of your filament guide tube.
This version comes with a mounting bracket designed so the sensor fits between the filament spool and the end of the guide tube on a Replicator 2 or 2x. You dont have to use the bracket and could mount it with double sided tape, zip ties or the bolts running through the body on almost any machine.
Requires a 9V battery (not included). The power is only used when the alarm sounds, so if you use an alkaline battery (which have minimal self-discharging) it will not go flat for a long, long time - we estimate over 1 year.

Genuine FlashForge replacement upper and lower parts for Dreamer and Inventor

The 2 colour Hibert cube is printed on a Flashforge Dreamer at 200 microns (each layer is only .2mm thick); usingABS (usually Grey and Black, colours may vary). It takes 2 hours to print and has 5 Shells with 15% fill.
Size : 3cm square. 25g
Model designed by TBuser

This cable is for the Z-Axis motor on the Dreamer
Genuine Flashforge part

This genuine FlashForge part is for the left hand side of the gantry - it holds the two rods which the extruder carriage slides up and down plus the belt idler pulley

Delivery, unpacking and setup of a Bilby3D supplied desktop 3D printer within 40km of our Sydney base in Alexandria.
This does not include anything other than very basic training on the use of the machine. Additional training available separately.

This wear resistant nozzle by Micro Swiss suits a range of printers with an M7 thread and 0.6mm hole

This stand holds spools up to 70mm wide (outside of flanges). The spool flanges sit on rollers and rotate as the printer pulls in the filament.
IMPORTANT: there is a wider model. This edition is thin enough to fit in the cavity of some printers, but is only just wide enough for most spools. (other mode)
FEEDER TUBE SOLD SEPERATELY order here for: 1.75mm, 3mm

Simplify3D® is Integrated 3D Printing Software
Harness the power of your 3D printer and move up to better quality prints with Simplify3D® Software.
Import, repair, slice, preview and print… all from one integrated desktop application.
Simplify the process AND improve the end result. Both are possible!

Features:
- Build print files for a huge range of printers - all from one application which has both a quick and easy basic option AND an advanced option with control of more parameters than we have seen in any other software
- Support for printers from Printrbot, Makerbot, FlashForge, XYZprinting (DaVinci), Solidoodle, Ultimaker, Leapfrog, Airwolf, Lulzbot, Tinkerine, BFB, Rapman, Cubify, MendelMax and more. Full list here
- Unrivalled slicing performance: High speed slicing with great print quality
- Variable slicing settings: You can apply 40% infill at the base and 15% infill at the top, and change layer height at different heights in the model
- Advanced Multi-Part Printing: Even when printing multiple models at the same time, you can apply different settings for each model

Advanced Features:
- Intelligent support creation: You can create supports automatically, or add or remove them with the click of a mouse, or both!
- Variable slice settings: You can vary layer height, feed, speed, temperature and more within the one print job so you can achieve the perfect balance of speed and quality. With wood filament, you can vary the temperature during printing to create a wodgrain effect between layers

This cable is for the Y-Axis motor on the Dreamer
Genuine Flashforge part

This cable is for the X-Axis motor on the Dreamer
Genuine Flashforge part

This fan is mounted on the rear wall of the FlashForge Dreamer
Genuine FlashForge part

Genuine cable for FlashForge Dreamer, Creator and Creator Pro 3D Printers

A lift out Glass bed, which will be super flat, and also safer and easier to remove prints from. It is 232 x 154mm and 5mm thick in heat resistent glass with polished edges for safety.
No brackets, this is just the glass plate. This is the size for Flashforge Dreamer, Pro and Inventor1 that comes in Glass Bed kit

This This wear resistant nozzle by AVN/Micro Swiss suits a range of printers with 1.75mm filament. It has an M7 thread and 0.2mm hole.

New Creator Pro 2016 (also known as the Creator 5). It features a steel chassis with a hood, display and navigation buttons, much like the Makerbot Replicator 2x (at less than a third the price).

Genuine Spare part for FlashForge Dreamer and Inventor 1 only heater cartridge.
Note : Flashforge Creater Pro cable is different (see image 3, ptHeatCart4024)
Flashforge Finder, Guider (1 and 2) and Inventor2 also have a short heater. This is not compatible

This is genuine FlashForge 3D Printer Filament.
The spool fits in the draw of the Finder, Inventor 2/2S/2SE and on the holders inside the Dreamer / Inventor

Genuine Flashforge spare part.
Compatibility: Connectors match the FlashForge Dreamer.

This is genuine FlashForge 3D Printer Filament.
The spool fits in the draw of the Finder, Inventor 2/2S/2SE and on the holders inside the Dreamer / Inventor

This This wear resistant nozzle by Micro Swiss suits a range of printers has an M7 thread and 0.4mm hole.

This cool upgrade kit gives your Dreamer, Creator Pro 5 (2016 Model) a lift out Glass bed, which will be super flat, and also safer and easier to remove prints from. (there is a different kit for the inventor 1). NOTE new machines have 12mm screws in corners and need 4 X 20mm counter head M3 screws- ask for them on order if needed

This 2017 upgrade to the trusty Dreamer adds an onboard camera and greater build height to the twin extruder, heated bed and fully enclosed features

This is genuine FlashForge 3D Printer Filament.
The spool fits in the draw of the Finder, Inventor 2/2S/2SE and on the holders inside the Dreamer

Genuine FlashForge thermocoupler
M4 brass fitting at sensing end (Note: our other thermocouplers and heater blocks are all M3)
Crimped terminals at motherboard end
~11cm lead length - Suited to the FlashForge Dreamer which has a terminal board on the extruder carriage

24 VDC Black brushless fan, 32mm between holes. 10mm thick. Lead length is 285mm.
It has 9 blades. Draws 0.1 A

This is genuine FlashForge 3D Printer Filament.
The spool fits in the draw of the Finder, Inventor 2/2S/2SE and on the holders inside the Dreamer / Inventor

This is genuine FlashForge 3D Printer Filament.
The spool fits in the draw of the Finder, Inventor 2/2S/2SE and on the holders inside the Dreamer

This is genuine FlashForge 3D Printer Filament.
The spool fits in the draw of the Finder, Inventor 2/2S/2SE and on the holders inside the Dreamer

This stand holds spools up to 96mm wide (outside of flanges). The spool flanges sit on rollers and rotate as the printer pulls in the filament.
Now includes 1 metre of 2mm Inner Diameter teflon tube and a strip of lint free cloth. If you require tube for 3mm filament, please leave a note when ordering.

This is genuine FlashForge 3D Printer Filament.
The spool fits in the draw of the Finder, Inventor 2/2S/2SE and on the holders inside the Dreamer

This quality chrome vanadium steel spanner is perfect for undoing the nozzle on your 3D printer with a MK10 style Extruder. Distance Across the flats, 9mm

This is a genuine nozzle from FlashForge. M7 tread.

This is a genuine FlashForge replacement sheet for the FlashForge Dreamer, Inventor1 and Creator Pro 2016 (v5) printing bed.
It is very similar to BuildTak but with more texture on the surface

This is genuine FlashForge 3D Printer Filament.
The spool fits in the draw of the Finder, Inventor2/2S/2SE and on the holders inside the Dreamer